Legend Tuned · Chip Tuning

SEAT Exeo (3R) 2.0 TDI 136 HP Chip Tuning

  • 2008–2013
  • Diesel
  • 136 HP · 320 Nm

Target with Legend Tuned Stage 1: 170 HP / 390 Nm; with Stage 2: 185 HP / 420 Nm. The original software is backed up, the calibration is tailored to the car, and the result is verified by datalog.

Legend Tuned figures

Stage 1
Power +34 HP +25%
170 HP Stock 136 HP · 100 → 125 kW
Stock
136 HP
Stage 1
170 HP
Torque +70 Nm +22%
390 Nm Stock 320 Nm
Stock
320 Nm
Stage 1
390 Nm

Figures are examples/estimates and may vary with the car's mileage, maintenance condition, fuel quality and hardware. Exact results are determined by dyno/datalog.

Power & torque curve

Stock vs Stage comparison

A representative power and torque curve with a technical table of all figures. Hover over the chart to see values by rpm.

Technical figures

SEAT Exeo (3R) 2.0 TDI 136 HP — stock and Stage figures
Value Stock Stage 1 Stage 2
Power136 HP170 HP185 HP
Power (kW)100 kW125 kW136 kW
Torque320 Nm390 Nm420 Nm
Power gain—+34 HP (+25%)+49 HP (+36%)
Torque gain—+70 Nm (+22%)+100 Nm (+31%)
Vehicle
SEAT Exeo (3R)
Engines
2.0 TDI
Years
2008–2013
Fuel
Diesel

Figures are examples/estimates and may vary with the car's mileage, maintenance condition, fuel quality and hardware. Exact results are determined by dyno/datalog.

Custom software · 6 options

Custom software options for this engine

Legend Tuned functions suitable for this engine, which can be applied in the same session as Stage software or on their own.

Stage 2 hardware, peace of mind and process

Stage 2 requirements

Stage 2 ready with the Custom Sport Filter Kit

At Stage 2, the engine's breathing is freed up with hardware, and the software is written to match that hardware. The target for this engine is 185 HP / 420 Nm.

  • Air intakeThe made-to-measure Legend Custom Sport Filter Kit or an intake suited to the car.
  • Intercooler & boostA vehicle-specific intercooler / blow-off valve to keep temperatures stable under sustained load.
  • Silicone boost hosesHoses and pipes that withstand the higher pressure.
  • Health checkIgnition, fuel system and clutch checked for this power level; the job takes ~4–8 hours (depending on parts fitted).

Included every time

Power with peace of mind

  • Original software backup — the factory software is read and archived before the job.
  • Reversal — the car can be returned to its original software whenever you ask.
  • Datalog check — boost pressure, ignition and air/fuel ratio are recorded and checked on a road test.
  • Vehicle-specific calibration — not an off-the-shelf file; tuned to the engine, hardware and fuel quality.
  • Pre-tune diagnostics — fault memory is read and engine health is checked before the software.
  1. Book

    Tell us about your car and your goals; we'll plan the day and time together.

  2. Analysis & backup

    Fault memory is read, the ECU is identified and the original software is archived.

  3. Legend Tuned software

    Calibration tailored to the car (Stage 1: ~1–2 hours).

  4. Test & handover

    Verified with a road test + datalog, then handed over with a walkthrough of what was done.

SEAT Exeo (3R)

Other engines in the same generation

All engines table

Vehicle Selector

Choose another vehicle

Start by selecting a make.

Stage 1 170 HP +34
Book an appointment